Hole Saw Kit, SUNGATOR 5-Piece Set. Specially Constructed Heat Treated Carbon Steel, High Precision Cutting Teeth. Cut Clean, Smooth, and Precise Holes Through Wood, Plastic, PVC Board and Drywall.

I purchased this item to cut a hole in a 1/2” round wooden board to to use as a small umbrella table for my patio. The product does not come with directions, however, it was fairly easy to figure out, and Im in my 60’s. Worked perfectly and Im very happy with the result.

Drill a hole, and it wor

I used this to cut a hole in a sink and it work very well .

The battery dies in my Barska gun safe and they gave me the wrong emergency key. I pulled out my hole saw and I was in my safe in 5 minutes and the hole saw is still cutting like a champ. Doesn’t say much for Barska but these hole saws are great.

Needed to drill some hole of a couple different sizes in some plastic/PVC pool equipment. This little kit works well, and is super affordable. No complaints.

These are not bad at all. Only reason why people keep saying it became dull is because they overheat the bits. Probably not using it with impact drill. I used it with regular drill and it worked perfect. I used it on my desk. I just had to do it for a few seconds, then spray some water and repeat. It came out great. It took about 10 minutes to drill the 1 inch thick desk because after about 2 minutes, it gets really hot. I had to dip it in cold water. If you dont cool it down and keep going, teeth will become dull due to heat

The set does everything I need it to do. I have cut the 7 holes I needed to get done, and they all went easily. BUT... like others, I wish the smaller pilot would fit a 3/8 drill. Like others, I had to use a 1/2 drill for every hole, whether the small pilot or the larger pilot. So it missed 5 stars throughout simply because a few thousandths on the small pilot made me use a much larger and heavier drill to drill a 3/4 hole. The saws cut well... low speed, cutting oil for the metal, and no discoloration or loss of edge that I could see.

Bought this to fix the previous plumbers laziness. Had to poke a hole though a 2x4 then 1/2 osb and as all home improvement projects go just a sliver of floor joist. Mounted the size I needed chucked it up on the trusty 20v lithium drill and let it eat. Cut through the 2x4 like butter. Once I got to the osb we were making heat like jet engine exhaust. Pop through the osb and find that edge of the joist and thats when the going gets tough. See between the osb and 2x4 I had some high quality 1997 era linoleum, super heated linoleum makes it near impossible to remove the slug you just cut. This is where I have issues with the tool, everything prior is my fault and the previous guy who took the easy road. I took the saw off the chuck, mind you its somewhere between 150 and the surface of the sun in temp. Once I clear the mess and go back at it the nut will not stay tight, had to let it chill on the window sill here in the December midwest to finish the job. Overall it worked, 2nd hole was just osb so that was a walk in the park. For what you pay it does well.

I used this to cut a hole in a sink and it work very well .

Great bi-metal saw set, not contractor grade. (But you already knew that) Nothing to complain about for me, makes holes in all sorts of things and does a good job. The first drill included was bent so the hole was out-of-round and bigger than it should have been. Removed and checked the other two INCLUDED drills and they are nice and straight. Even if they werent, drills are cheap and makes the whole thing work awesome, wish other reviewers would quit complaining about the small stuff. The hole saws themselves are deep and true, but the way they attach to the bit makes them wobble a little and therefore are not going to make a perfect hole. So you get what you pay for. However they work well and suit my needs just fine!