5 inch HSS BI Metal Hole Saw Cutter 1-1/2 Depth with Big Arbor for Wood Metal

Arrived on schedule. Good quality, cut 4 hole in 1 /2 plywood. Came with the arbor, 2 center bits, a bonus smaller hole saw and a small tape measure. If I needed to use a hole saw every day, I buy a Lennox or Diablo. This is perfect for the few times Ill need to use it.

Very sturdy and durable. What youre cutting will get stuck but there are holes to push product out.

Needed to cut some holes for kitchen exhaust pipe, and this worked spectacularly cutting through some pine. But, then I had to cut through the roof, and of course asphalt shingles present a problem. But, that was the last hole so I committed myself. It got through, eventually, but I dont think it liked it. In a couple years when I need to cut another 6 hole Ill give it another try, but he already did his duty so I wont complain if he takes a bit longer.

This huge hole saw works fine in a drill press when you clamp your material down. Using this with a portable drill is another matter entirely. The blade is too coarse to cut smoothly and will catch and try to break your wrist. If you attempt it, use a drill with a clutch and go slow. I have only used it a few times so can’t comment on durability, however I would purchase it again.

I bought this cheap 5 holesaw to cut through a 1 thick piece of steel. Not just any steel, it is 4140- a chromium molybdenum manganese alloy. But wait- not just any 4140, it is hardened 4140, 32 on the rockwell C scale. A lot of 4140 is sold in the annealed state for easier cutting, but then needs to be hardened afterwards to gain the strength benefits of this alloy. I verified the 32Rc myself, cause I believe it matters for what Im making. Anyway, this holesaw cuts it fine. I ran it at about 70 rpm, a little faster than 1 rotation per second. A little less than 100 fpm linear speed. Using a pecking motion, lubrication, allowing chips to clear. Many drill presses and most hand drills just wont go that slow. If you put this in a hand drill and think youre gonna cut even a piece of sheet metal, its going to be hard to control, and if you spin it fast (like the 600 rpm speed that seems slow in your 1/2 drill) you could probably dull this in seconds. That is just the nature of a large diameter cutter like this. If you overspeed it in metal, you WILL ruin it, in seconds. This saw isnt magic metal, and neither is one that costs 3 times as much. This was used in a milling machine..it is rigid, and can go slow. If used to cut a hole in your ceiling for a lamp, you could get away with a lot, none of this applies. The saw wasnt real round...I checked it and improved it a little by hitting with a hammer, checking, hitting, etc. BUT- more expensive brands are no better at all, they are always pretty out of round..unfortunate, but good enough. Tight quality control costs a lot. You want a $150 hole saw thats somewhat better? Ill deal with a cheap one, myself. It is a roughing tool, no more. It pains me to see most drills and holesaws oversped by users who then dull it and blame the tool!

I purchased this for cutting speaker holes in fiberglass (boat) I didnt want to spend $50 at one of the big box stores. The hole saw is good quality (better than expected) I would not hesitate to order another one.

Inexpensive compared to name brands but worked perfectly for me cutting a half dozen holes through 2 layers of wood (3/4 incl solid cedar plank backed by 3/4 inch plywood sheeting) still looks knew. Needs 1/2 drill for power. As another reviewer pointed out, use an auxiliary drill handle. Hole saws can bind (did it twice) and the drill torque can seriously strain or otherwise damage your wrist. But saw cut clean holes every time

Seems very well made. I had four holes to cut to install a 6” duct for the microwave/ventilation hood to the outside. I was thinking at this price it might not hold up but to my surprise I think it would cut dozens of times before it becomes dull. My cabinet back is plywood and the wall is tongue and groove lumber, and it cut with no problem. You will need a drill with a 1/2 inch chuck then don’t force the cut just let the cutter do the work.

I bought this to put the hole in cornhole board. It cut through great. Glad I had a big drill with side handle to keep it level and from hurting my wrist though.

Worked great for 5” Halo Old Work Can lights.