Brush Research FLEX-HONE Cylinder Hone, BC Series, Silicon Carbide Abrasive, 3 (76 mm) Diameter, 240 Grit Size

I have six of these now, and I buy a new one if I need a size I dont have. They work perfectly to take the glaze off of a motorcycle cylinder before installing a new piston and/or rings. They are sturdy, and last a very long time if treated well. Pro Tip: Dip them in transmission fluid before honing.

Got it fast and item as described. Love it.

Did 2 passes with the 240grit on a RM250 cylinder and it came out beautiful , real smooth

I used this to clean up the slide hole on a caliper on a 13 gmc 2500HD. Worked good and cleaned it right up. Wish I thought of using one of these sooner! I did notice a bit of wear on the stones after one use but not overly concerning.

If you are only a tiny bit over the nominal size do not follow the instructions and go up one size. They are oversized to begin with (my 1 1/8 hone being a few thousandths shy of 1 1/4). I bought a 1 1/8 hone to remove the seam from 1 SCH40 pipe and open it up from 1.03 to 1.06 so that 3/4 pipe will telescope in structural applications. I also intended to use it to open up 25mm aluminum C-cell flashlight tubes to fit 26mm LiFePO4 cells (1.026). I am hoping that after breaking in the hone on the steel pipe I will be able to start it in the aluminum tube without damaging the end. I think in both cases I would have been better served in not following the instructions and buying the 1 hone instead.

If you are only a tiny bit over the nominal size do not follow the instructions and go up one size. They are oversized to begin with (my 1 1/8 hone being a few thousandths shy of 1 1/4). I bought a 1 1/8 hone to remove the seam from 1 SCH40 pipe and open it up from 1.03 to 1.06 so that 3/4 pipe will telescope in structural applications. I also intended to use it to open up 25mm aluminum C-cell flashlight tubes to fit 26mm LiFePO4 cells (1.026). I am hoping that after breaking in the hone on the steel pipe I will be able to start it in the aluminum tube without damaging the end. I think in both cases I would have been better served in not following the instructions and buying the 1 hone instead.

I have personally relied on products from this company for a very long time in a professional setting. As far as ball Hones go Flex-Hone is the best and has been. The quality is top notch and the number of sizes they make are unequalled by any other company

Used this to hone both cylinders of a 22 hp Briggs VTwin lawn tractor engine that needed a new connecting rod, a new piston and 2 sets of rings. Honing the cylinders is needed to allow the rings to break in and seat properly. Since I don’t expect to do this regularly I was between a cheap set of honing stones for around $20 and the Flex hone which I’d seen on YouTube and was selling on Amazon for $37. The reviews on the honing stones were terrible (cheaply made and inconsistent result) and the flex tool reviews while not numerous were mostly positive. Several excellent YouTube videos by the manufacturer and a call to the seller about whether the 3 inch (180 grit) tool would be good for my 2.96 inch cylinder convinced me it would be worth the extra cost for the Flex hone tool. What a FANTASTIC result in less than 10 minutes to do both cylinders following the video instructions of coating the tool with clean oil and moving in and out of each cylinder for 1 minute. Perfect cross hatched pattern on both. Great tool and good value considering the $200 of parts and many hours of labor to complete this project.

Used the 3” 240 grit. Did an amazing job on the steel sleeves in this machine for a set of SPI pistons. Compression and performance are still spot on after 800 miles of use. Definitely would recommend.

Quickly gets the job done It was easy to get cross hatching