Noico 80 mil (2 mm) 36 sqft (3.4 sqm) car Sound deadening mat, Butyl Automotive Sound Deadener, Audio Noise Insulation and dampening

Loved it, I bought two boxes and used about 1.1/4 boxes on the floor of my 2001 f250 diesel. I was able to go from 89.3 dbs inside the cabin to 77 dbs

Just finished installing this in the main cabin of my 98 Jeep TJ. I pulled the OEM carpet out, center console, and the rear and passenger seats, then performed a sound test using a db measuring app on my iphone 6s at 65 mph with the app running and measuring and held at head-height over the center tunnel. Outdoor temp was 91 F with high humidity at 3pm. Had soft top on with all windows on and closed as well as full steel doors with windows up. Had blower on 3rd highest setting to keep the soft top from flapping and slapping. Measured for one mile on level road. App measured a consistent 92db. Using one box of 80 mil, covered entire floor area and sides, excepting the tailgate. Measured db levels again-outdoor temp was 87 F with high humidity at 3 pm on the same level stretch of highway at the same speed with soft top on, all windows in, full steel doors with windows up and blower set on 3rd highest setting to keep the top from flapping and slapping. Measured for one mile, and app measured a consistent 71db. Returned home and installed new carpet with mass backing, center console, front and rear passenger seats, and measured again on the same stretch of road and same conditions of soft top and doors with blower on 3rd highest setting. App measured a consistent 64db. Interior is noticeably cooler as well, and the majority of noise is coming from the bare tailgate and the soft top. At 55 mph the sound level drops to 61db. Note that I did not install on the tailgate, inside the doors nor on the inside rear wheel wells. Given these results I feel that this product is well worth the price and the work to install. Definitely have leather gloves, a sharp knife, a silver and a black sharpie, some cardboard as a cutting surface, a roller, and a high powered hair dryer for heat-blow torches and heat guns are not necessary. When cutting and trimming, cut slightly larger than your pattern. For larger size install pieces, I recommend grabbing a helper at the least. If a helper is not available, then only peel 1/3 of the backing paper off from the area thats farthest from you and install that first. Once that is in, carefully peel off the remainder and slowly apply the rest. Start from the center of the sound deadener and smooth outward from there to remove air pockets. Roll with the roller until you have flattened or mostly flattened the little triangles in the foil. Save all of your offcuts so that you can fill in the irregular shaped areas later. Start with the largest areas and cover those first. Keep a small bag or box handy to put all of the little pieces you trim off-this will keep these from becoming a mess later. Take your time and budget twice as long as you think you will need. Hope this is helpful.

its very easy to apply. pretty good adhesion, but not like the high-end stuff (secondskin). the Aluminum is pretty thin and easy to tear (sometimes undesired). but its a great price point. id give it OK/3 for quality, but 5/great for price.

It made a noticeable difference, but on my Nissan Rogue, it is still a very noisy car. My F 150 is 100 times quieter without doing anything.

this is awesome i bout 4 boxes of this better then that spray crap

wow this stuff works great! very happy with the fit and function. and by fit i mean it is really easy to apply and sticks to anything! i had to cut some custom sized pieces for the inside of my doors and walls and wow instant difference in noise. my extended van is as quiet as a mercedes now and im not even done with the whole thing. i would recommend this product to anyone interested in sound deadening. dont waste your time with the sprays and dont waste your money on the big dollar stuff. this is a unbeatable value!

I bought one box to do the interior of my TJ. It’s lifted with aggressive tires and the exhaust dumps under the cab, so the noise was pretty bad on the freeway. You had to yell to have a conversation. Phone conversations were out of the question One box did about 90%-95% of the interior. Got the entire floor done, and about 70% of the rear wheel tubs. Afterwards it’s a huge improvement. You can have a normal conversation, my kids don’t complain, and the exhaust no longer resonates in the can. $65 very well spent. If I bought another box I would finish the tubs, get up on the firewall some more, And get the interior of the doors. I’m happy for now.

It cut easily, the adhesion is great, had embossing on the aluminum to tell when you have rolled it on properly. Does not want to come off after installation unless you really try. Be sure to tape the edges with aluminum tape to keep the butyl material from being exposed. Used in the trunk, inner fenders and under the seats and floors of my Fiero.

Easy to apply, good for making an old car “sound” like a new car!

Easy to work with, just using in my trunk, it enhances bass Id say 30%. Excited to get my doors done next!