Comgrow 3D Printer Warm Enclosure Fireproof and Dustproof 3D Printer Tent, PVC Laminated Polyester Constant Temperature Protective Cover Room for Ender 3/Ender 3 Pro/Ender 3 V2/Ender 5 Pro

(917 Reviews)

Price
$49.99

Quantity
(10000 available )

Total Price
Share
61 Ratings
48
6
2
1
4
Reviews
  • Dee

    > 24 hour

    Great product, Very big with plenty of room for my creality ender v2, and saved over $10 in costs. Assembly took a minute to figure out due to no instructions, but is very straightforward. Basically attach each pole that has a letter to each pole that doesn’t have a letter, so that they are 2 poles long. Then stick them in the white adapter, so that each letter is parallel to the same letter. Definitely recommend this; don’t waster your money on a more expensive one.

  • Hsiang

    > 24 hour

    It was easy to assemble and works as intended. It would have been better if there was a top opening. Some filaments can benefit from it. For example, PETG prints better with all sides protected from draft but with top open to help keep chamber temperature in check.

  • Kindle Customer

    > 24 hour

    This does the job. Its a bit pricey for what it is, but they all are. It could have been engineered with less varied tube sizes, buts opts for four different sizes, so pay attention to the directions (its not hard). The corner joiners are plastic, so dont let anything stress them or youll be... printing a replacement piece, I guess. It is an absolute dust magnet. Thats fine, I wanted it to keep dust and drafts out, it doesnt have to look pretty while doing it. The important thing is that it fits the Prusa MK3S+ with room to spare. Now I guess I need to buy some LEDs.

  • Richard Menzano

    > 24 hour

    Great low cost enclosure

  • Kat W.

    > 24 hour

    Perfect fit for our Creality Ender 3 Pro. The quality is better than I expected it would be... thick, slightly tough/rubbery on the outside, sturdy zipper. Pretty pleased with this.

  • ahero97

    > 24 hour

    I’m almost positive this is actually a grow tent for growing indoor plants but it was the cheapest option and I’ve very satisfied. Helps hold in the heat perfectly and it help keeps dust from getting in during prints. My Ender 3 pro which has the spool up top fits perfectly with room to spare.

  • ty c

    > 24 hour

    A bit of a challenge to assemble but other than that no complaints from me. Its a nice little enclosure. I just wish my Elegoo Neptune 3 wasnt a POS.

  • Deej Swee

    > 24 hour

    Fits my PRUSA with room to spare. I added some led lights for interior lighting. Happy side note, if you get the motion activated LED strips from the store 5 below…..you can have lighting only while the print head is moving.

  • Buys Too Much Stuff

    > 24 hour

    Fits a Creality 3 s1 pro (hey… don’t judge me… it was free… the Creality thing, not the enclosure) with all sorts of th3d add-ons and the Creality klipper tablet with room to spare. This is a full enclosure - not just a 5 sided box to place over the printer - so it’s good for catching all the little bits of plastic that would otherwise fall on the floor. Comgrow did a great job on this.

  • Anon

    > 24 hour

    It is easy to assemble but the enclosure was too big to fit where I needed it to, and for some printers it may be too small to hold. I am also not convinced it will work super well as there are some holes where velcro is attached.

Comgrow 3D Printer Warm Enclosure Fireproof and Dustproof 3D Printer TentComgrow 3D Printer Warm Enclosure Fireproof and Dustproof 3D Printer Tent
AdvantageAdvantage

Related products

Shop
( 2033 Reviews )
Top Selling Products