Hakko FX888D-23BY Digital Soldering Station FX-888D FX-888 (blue & yellow)

In the middle of a project my old (very old) Radio Shack soldering station ceased functioning. For several hours I looked at replacements, Read all the reviews good and bad. Watched some Youtube videos and finally decided on the the Hakko FX-888D. I never pay for overnight or 2nd day delivery but I really needed a soldering station to continue my project and was glad I did to get back to work. The Hakko heats up fast, very fast. Especially compared to the old Radio Shack. I bought some extra different shaped tips. This is my first experience with a tip that isnt a larger/medium cone shaped tip. So far so good. I have had the unit for a week now and have used it every day and I have been very happy with the purchase. Why only 4 Stars - The enclosed documentation is missing 5 pages. The document enclosed talks about the presets but doesnt show you how to. The documentation does have a reference to a web site where you can get the full set of instructions. The 5 missing pages include 3 pages for doing the presets. The other 2 pages are details on the parts and the internal construction of the unit. Its a little point but the cost of a couple mores pages of paper cant be a profit breaker. So for now only 4 stars - but very happy with my purchase so far.

I purchased this because I had to solder a new USB port to my Yeti Pro microphone and also to solder a custom build keyboard. I have little to no experience soldering onto PCBs but with the few videos that I saw online, I was able to create beautiful and consistent solders in both uses. The temperature ramped up very fast, and the digital interface shows the temperature as its climbing. I thought it was a bit weird that it only had one up arrow, but for a hobbyist, the temperature control is very easy to work with, although I imagine an electrical engineer that needs to change temperatures often would find it to be a pain. I used the brass cleaning foil after each switch I soldered, and the tip stayed clean throughout the process with no oxidation. Im not quite sure what the sponge is used for, but good to know that its there incase I find a use for it!

Ive been saying that Im learning to solder for a long time now and thats because I never purchased the proper iron and so I thought it was the fact that I lacked the skill and know how. Now I know the cheaper irons, which I have 2 of, one is not temp controlled and the other just didnt get hot enough. If I would have known that I just needed to invest in a great iron, I would have empowered myself a long time ago. Its sturdy, easy to use, easy to change the controls and I like that the power unit is separate from the holder. The only thing I would suggest is if you are soldering pcbs youll probably need to purchase an additional tip as the one included works but is a little wide for tiny pcb probject IMHO.

Yes, the build quality is good, and yes, it does the job well. Theres something you should know before buying it, though. I wish I had known. Other reviewers have been very charitable in describing the controls as not intuitive. For the sake of forewarning future buyers, Ill be blunt: The user interface is a steaming pile of... um... garbage. You get a three-digit display and two buttons that each serve multiple functions. That design decision alone was foolishly stingy, as others have noted. A knob and another digit (for displaying short words) would have done wonders, and I would gladly have paid the extra $3 in hardware costs. Especially since these controls are required for even the simplest of operations, like setting the temperature. The two buttons you get are labeled: UP and ENTER, but those labels are misleading, because neither matches the corresponding buttons function in the devices normal operating state. If you find your way into the settings menu (which you cannot do with the buttons alone) the four top-level categories are represented by mysterious, disjointed numbers: 01, 03, 11, 14. Even if youre a programmer who habitually translates decimal numbers to binary, this menu is still meaningless. Its all the more insulting to discover that letters *can* be displayed, as they are in the submenus; just not here, the menu where they are arguably needed most. Want to raise the temperature while youre working? Pressing the UP button wont do it. You must hold the ENTER button for a while, then wait, then repeatedly press the UP button until the first digit of your target temperature appears (and then nine more times if you overshoot), then press ENTER, and then do it again for each additional digit, until the display shows your target temperature and you press ENTER a final time. Its like having to program a 1970s/1980s videocassette recorder... just to adjust the temperature of your soldering iron. Okay, that madness is not the end of the world, but adding injury to insult, can you guess what happens if you accidentally (and understandably) hold the UP button instead of ENTER to adjust the temp? It takes you through the same procedure, making it look at first like you succeeded, and then reverts to displaying the original temperature. Want to know why it didnt work? That was the procedure to recalibrate the machines temperature control. Congratulations: Now every temperature the machine displays is wrong, and will remain wrong even after a power cycle, because the machine tricked you. Oh, and it doesnt tell what happened, so its very possible that youre now soldering at a much higher temperature than you think. I hope you didnt damage any components. What if you somehow figure out what happened and you want to fix it? Too bad. The manual doesnt tell you how. It doesnt even mention that it can be done. Youll have to wait until you can reach Hakko support, or else find a note online from some other unfortunate soul who was also burned by this unforgivably awful excuse for an interface. I hope it happened during business hours and you have a phone nearby, or youre someplace that has internet connectivity. For the record, here is the secret factory reset procedure: 1. Turn off the power switch. 2. Hold the UP and ENTER buttons. 3. Turn on the power switch with those buttons still held. 4. Wait until the display says A. 5. Release the buttons. 6. press UP to make the display say U. 7. Press ENTER. I hope that saves someone some trouble. Dear Hakko, Please do better in the future.

The price on this unit was more than I usually like to pay, which is why Ive struggled most of my life with inadequate soldering irons. But one day, while trying to take some capacitors off a circuit board, holding the iron on there endlessly in frustration, I decided enough was enough. I scoured the reviews in Amazon, initially looking at a Weller unit, but someone pointed to the Hakko unit and I was impressed by the number of positive reviews. So I plunked down my hard-earned cash, and waited. One week later, I unboxed the unit, noticing the solid construction. And after trying it, I knew I had reached soldering iron nirvana! Here are the features I really appreciate: 1. Hot in seconds flat. Theres a little red LED on the front that tells when the iron is heating. When it goes off, the tip is ready. I didnt time it but turning the heat dial up half-way only takes about 5 to 10 seconds before the tip is ready. Wow! so different from what I was used to. 2. Performance. Most soldering can be done at about half temp. A few times Ive cranked it up all the way, to melt some stubborn joint, and it really works! 3. The brass tip cleaner. I really like the little brass wool that you can rub the tip on. It works very nicely and is much more convenient than water/sponge (although you can use that too). 4. Good stand. Its solid and doesnt fall over easily. Same with the transformer-temp control unit...its really heavy. 5. Flexible cord. Dont you just hate it when you get a tool that has a stiff plastic cord that never seems to straighten out? Well this one doesnt have that. The cord from the iron to the controller is nice and flexible. 6. The heating takes place so quickly that as soon as Im done a joint and have a break, Ill just dial the temp down and leave it on low, knowing that I can get it back up in less than 10 seconds. Im sure that helps the tip last longer. Theres really nothing not to like about this unit. Well, the tips are a bit expensive (about $10), but they look like they will last a while. Ive also seen some sets of tips on eBay for less...not sure about the quality of these though. Im in my early 50s now, and am a bit ashamed that Ive been doing occasional electronics work for about 30 years without such a good tool. Im pretty sure, unless my unit suffers from a defect, that this will be the last soldering iron I buy for the rest of my life. Should have bought it a long time ago...

It was fine but I ended up replacing it with a pinecil, which is less bulky, way more controllable, and has all sorts of cheap tips available.

I purchase my Hakko 888D August 3, 2013. It is simply the best soldering tool I have ever used. Heats quickly, and maintains its temperature very well it makes assembling stuff like PL-259s a snap. The adjustable temperatures are are real nice you can dial it in from, 120 to 899 degrees F. So what ever soldering situation, and alloy of solder you have it covered. There is a large variety of tips and others have told me they last for years of much heavier use then I will ever give mine. A very important thing in how the manufacturer supports their products. My 888D took a plucked goose dive off of the bench, it shattered the plug, and cracked the front panel skin. I thought I was going to have to purchase a new one but a check at the Hakko USA website revealed they have all of the necessary parts to repair it. I called their customer support line and the phone was quickly answered and Mary took my ordered for the replacement parts. The front panel skin was temporally out of stock. I was told they would be restocked around the 2nd week of March. I received the parts I ordered that where in stock in just a couple of days. I waited until the start of he 2nd week and used Hakko-USAs live chat line and asked and was told the parts where indeed in stock and was told to call. I did so and the phone was quickly answered and I was able to order the front panel skin which arrived well packaged in just a couple of days. When I took the control unit apart the quality of its design and construction was notable. A high quality control board, with quality parts, large and heavy transformer not at all a cheapy. A real nice touch is the length of the point to point wiring to the plug is much longer then is necessary which makes installing its replacement very easy. The repair was straight forward and the Hakko is once again in service. The worst part of the repair was being forced to use a crummy old Weller pencil.

I put this title in for a reason. My previous experience (other than soldering copper pipes) has been with various soldering guns, but Ive also had a couple soldering irons, ranging from fairly powerful to low wattage for fine. The soldering guns, even the Weller brand ones, invariably died after a while, with lack of heat, intermittent heat due to mysterious issues and rattling. Soldering irons also died, with cracking bakelite handles and tips that got loose. Using this soldering station is incredible different. Soldering has become much more consistent, the tip stays clean and attached and its ready to go in seconds. Playing with the temperature is really nice, to get just the right amount of heat in the right amount of time. Its got good power too. You dont really need 250 W if the temperature is controlled and heat is transferred well. Already this has lasted much longer than any $40 soldering gun would. I love it and thats why Im saying this is a must have. Typical excellent Japanese quality.

Ive used this product extensively at my previous electronics company, and it was always beyond dependable and the temperature accuracy was usually very good. We still had to calibrate it every year, but it was never too far off. Pros: Will melt any solder that I worked with. Its temperature range is more than adequate. If you need any hotter, youll surely damage a component. Comfortable grip, and never had an issue with its holder. It displays the temperature as it is reaching your desired temperature, which is nice to see how long you have until its ready for you. Nice to have a brash mesh to clean the tip, albeit I seldom used it. Changing tips is quite easy, as long as you dont accidentally weld it on (keeping it on max temperature for an extended period of time will do it), but parts are relatively cheap if you do, as you will surely break it (if you weld it). I would say its irons leash is a perfect length, measuring around 4 ft. Power switch is on the right side of the unit. Cons: Now, I am nitpicking here. It does have a digital input and it takes a little bit to change the temperature. I do prefer an analog knob for my soldering station so I can easily change temperature rapidly. However, some people may find a digital display is more professional. Its non-square sponge holder means a basic yellow square sponge will not fit without some modification. Tips can be expensive, but can easily last a year or two of heavy use, if you take care of them. All that said, I would still definitely recommend this product. It is much better than just a plug-in iron. Very well priced as it is definitely a professional grade station, but more than welcoming to the amateur hobbyist.

My first professional soldering iron was a Weller and Ive always been skeptical about anything else. We use Wellers at work. Well, this guy gave this model a very nice review - better than the similarly priced Weller, so I went with it. The things I do not like: 1. That silly sponge. I will probably replace it. It is functional, but I dont care for the feel of it. I like to abuse my sponge. Always keeping the tips clean and shiny. This is less than perfect. 2. The UI should have been a 2 button up-down configuration. What I like: 1. It maintains its temperature ferociously. When soldering solid copper wires, this is a big help. The thermal output is great and it maintains temperature like a beast. 2. It has a great feel overall. Solid. 3. I bought a tip assortment from Hakko, but the tip that comes with it is a great general purpose tip. good for all but the smallest SMD parts.