When paired with motion sensors (or manually /w smartphone), my switch is part of an electronic team to (among other things) light/darken zones as people/things move through. Exactly what I needed.

Bought this to primarily operate outside lights to come on at dusk and off at dawn. Was easy to install, however, was not mentioned in instructions that it had to have a common wire connected. Only after it not working and searching internet did I find this requirement. The only other thing negative about the switch is that its meant to be used alone as a single switch. It is all plastic and there is no hole to attach a face plate to, except the one it comes with, which snaps in place. I wanted to use it in a double gang setup as shown in picture. There are holes in it which line up with the face plate, however, they are not threaded and too small for standard face plate screws

I recently installed this light at the opposite end of my home from the hub, and the response time is excellent. I called customer service to figure out if the red LED light could be turned off, and a human answered the phone on the second ring. Excellent customer service. The only complaint is the bright red LED light that activates when the switch is off. I was able to pop off the front of the switch and cover the light with a small piece of black gorilla tape. Problem Solved. I will be first in line to buy when they come out with a dimmer light switch.

The Yolink uses LoRa connectivity which has been for me way more reliable than any of my WiFi connected devices. While I have not tested this switch over a quarter of a mile I do have another YoLink on my mailbox which is quite some distance from the house and it reliably notifies me when the mail shows up. I did have a problem with one of my switches which was quickly cleared up by the Yolink support as I had inadvertently miss wired a switch. The switch plays very easy with Alexia.

I really love the yolink ecosystem. they are super easy to add to the system, so i was excited to migrate from my zwave switch that controlled my outside garage lights to this system. Overall it works and does what it is designed to do, but i do have a few minor issues i hope they address in future light switches. 1) As most others have noted, the red LED light is sort of annoying. I have it in the garage so it isnt that big of a deal, but i would not want these throughout the house in main living areas. THe red indicator light when off is just very bright and annoying. I would rather it be a very small led indicator in the bottom corner. Or if you could change the LED maybe a different color would be better, and/or brightness level. if that was controllable. When on it is white which is fine. 2) The overall feel of the switch is not the best i have seen. Where you make the connection for the electrical, the screw is what bites into the copper to hold it in. It does make a very secure connection when tugging, but most other switches have molre of a plate that squeezes the cable on the inside. Again it seems to be ok but just something i noticed. 3) My switch came with the arrow facing down (opposite of the instructions which tell you to have it facing up). Support noted it was fine to install, but again just noting that it was not what the directions had. 4) THe switch housing is a little thicker than the other traditional switches, so i think my cover plate was not fully flush on the one side. i took a picture so you can see although it may be hard. Id rather it be designed more like a traditional switch and if needed be able to tear off the ears as some setups do require that. 5) I would have loved if this was an energy management capabilities to keep track of how much power, but not a deal breaker, especially at this price point. 6) The software does have sunrise/sunset scheduling, but i am hoping they include more advanced such as x minutes before and x minutes after to tweak my settings a little better for my needs. Again overall i like it and great price point but hopefully they address some of these in future models.

I have been using yoLink products for since they were invented and every single item works flawlessly and integrates into alexa speakers- giving me warnings, alerts and notifications of temperature, mail delivery, motion 500 feet away at my barn, barn door contact alerts, steam room and sauna door alerts (grandkids wandering), water leaks in 7 locations as they occur in my home, etc. This is flawless! Im waiting for cameras and I will totally kill xfinity home!

Easy set up

Works great with the YoLink hub and even better when paired with a YoLink motion sensor. You can connect the sensor directly with the switch and lights turn on instantly. You will need to pigtail a neutral wire which is not included. And unfortunately no three-way control. Overall a great product though. Good customer support as well.

It takes getting used to only 1 way switching on/off but super simple to add and works like a charm! Replaced a bad switch and now alexa controlled as well. I can access from my phone and all yolink product is very easy to use and run on the app. Connection time is very fast. I have to say this to all my product.

The wall switches work as advertised and I love the fact that I can light up my back yard and side yard from my phone. From my shop to the house is about 75 feet. Works GREAT from the phone. Lights are super bright and light up the entire area just as I was hoping. I wasnt looking forward to digging a trench from the house to the shop to bury a line to operate the outside lights. Now I dont have to. YOLINK took care of that for me. Just built the shop and in the process of wiring it up now. YOLINK is going to be installed as I go along. Once I get the house / shop all equipped with the required YOLINK items we, then I will start on connecting them to work together. So Far I am impressed with the quality and simplicity of the system.