DC HOUSE 12 Inch 12 High Speed 14mm/s Linear Actuator Motor 1000N DC12V with Mounting Brackets

(0 Reviews)

Price
$39.99

Size
Quantity
(40000 available )

Total Price
Share
92 Ratings
39
20
16
3
14
Reviews
  • Dion Schulist

    > 3 day

    This actuator works great

  • a w morgan

    Greater than one week

    Had a problem with actuator, contacted ECO by email. Company sent me a replacement in short order. Product works great. It is a real pleasure dealing with a quality company. Will definitely deal with them again!

  • Kayley Lynch

    > 3 day

    Very quiet Smooth and runs fast

  • K Fry

    > 3 day

    Generallly this works OK, and meets its specs. However, the machining of the mounting pin holes is shockingly bad. Ordinary good manufacturing practices produce products with better tolerances than a hobbyist machine shop can. This is much worse than hobbyist machining level. The pin hole (at the motor end) is not perpendicular to the rod, which can be checked by mounting the actuator in one position (eg. motor facing east), and then remounting it after rotating it 180 degrees. On mine, the difference in rod end position was about 1.5 inches, meaning that the hole was drilled a couple degrees from perpendicular. Some hand filing with a rat tail file trued mine up enough to prevent binding, but of course, the hole is no longer round or straight. Suggested improvements: stainless steel anchor brackets and pins to make it more suitable for use outdoors. And, of course, standard machining.

  • Angel Hermann

    Greater than one week

    Went to use it and it doesn’t work - hooked it up to 12 volt and nothing works

  • Nanette J.

    > 3 day

    Worked fine until temps dipped below freezing. It is mounted under chicken nesting boxes set deep inside the coop, out of the weather. Freezes every time below 32 degrees. That was the whole point in purchasing, so I could open from my phone in freezing weather. Complete fail!

  • B. Money

    > 3 day

    Used this actuator to control a pivot on a project. First, the actuator is extremely slow operating. Second, it snapped off the rear mounting ear (on the motor housing) on the first use. Its made from extremely cheap cast aluminum and the second it got tweaked, it snapped clean off. Not sure of the actual force limit of this item because the design failed before I could really test the force limits of the unit. Maybe I torqued the actuator across an axis I didnt think I was, but this shouldnt be a failure point given the rating of the actuator.

  • Christian V. B.

    > 3 day

    Es bastante robusto, pero es demasiado ruidoso, sobrepasa los 50dB que ellos indican

  • Gary C. Ruisinger

    > 3 day

    Bought this for a router lift. Works perfect. Extends fairly quick, about as fast as I can manage anyway. Lifts the 35 pound load with just 10 watts of power (.8 amp). So far the quality seems great, time will tell. Unit seems well sealed so I dont expect any problems with dust and no water as it is an inside application. Very pleased with the speed. A++

  • James

    > 3 day

    Use to lift a trolling motor

Product features

➤Specification:Stroke length = 12 inches (305mm);Travel Speed:0.55in/sec(14mm/sec); Retracted length = 370mm(15"); Extended Length=620mm(25”);Maximum current draw = 3Amps; Maximum Load = 225lbs(1000N).

➤Material: Aluminum alloy housing, IP54-rated protection sealed against dust, water, and corrosion suitable for outdoor use. The internal limit switch automatically switches off when it reaches in case of the motor idling.

➤Great Performance: with reliable performance, stable running, the same characteristics of push and pull, and good environment adaptability, etc. 

➤Application: Widely used in many industries, such as electric power, machinery, metallurgy, mining, petroleum, chemical industry, transportation, lifting, construction, food and feed processing. 


INSTALLATION WARNING:

1.The load added onto the actuator must be less than or equal to the rated load of the actuator. 

2.Mount the actuator by securing the top and the bottom mounting holes to two fixed positions. The stroke length of the actuator and the limitations of the particular application will determine the location of the fixed mounting positions. 


IMPORTANT: 

1.Confirm that the two-way movement of an item is smooth and within the actuator"s stroke length after it has been installed. Additionally, confirm that no obstacles exist along the travel path of the actuator. 

2.Secure the item"s top and bottom mounting holes onto the two mounting fixtures using 5/16"" diameter bolts. 

3.Connect the red wire to the positive post and the black wire to the DC power supply"s negative post.

4.The operation of the item should be tested manually after the installation is completed.

Related products

Shop
( 1610 Reviews )
Top Selling Products