The springs alone increase the quality of life with your printer. I rarely have to keep leveling the bed (even with a BLTouch). Having an all metal extruder is also a must have.

You wont really know why this is such a great update until you install it all the items. Definitely worth the purchase and if you have an Ender3 v2, YES, Buy this upgrade! Feeding filament into the boden tube through the extruder is much easier as well.

The springs are amazing, add in BL or CR touch and youll almost never have to level your bed again. The extruder upgrade is needed no matter what. The oem plastic WILL break.

These springs are a serious upgrade over the stock Ender 3 Pro springs! I read a lot of notes saying that the stock springs just didnt have enough tension in them, and after every few print jobs I was having to level the bed again. Not the end of the world, but if something will solve that problem for under 20 bucks, and upgrade the extruder to aluminum, why the heck not go for it? Everything arrived quickly and was neatly packaged. After opening the bag with the bed springs and wheels, I was impressed. The springs are very beefy, the wheels are nicely made and have good grippy teeth on them, which will make fine adjustment much easier, plus the pop of red under the printer is a nice touch. Installation was pretty simple: Unscrew the stock adjustment wheels until they come off the screws. Lift the bed up (being careful not to damage the bed heat wires). Remove old springs. Then I set the rear springs in place and put the bed screws down through them to hold them in place, and then tilted front of the bed down and slipped in the front springs. It was a little awkward to get it all lined up, but nothing too bad at all. After that, I attached the fancy new adjustment wheels. I went around the bed, tightening each corner to around 25%, 50%, then 75%, then finally 100% of the way down. I figured I should tighten them up gradually to keep from twisting the bed or knocking anything too far out of whack. Happy with how things looked, I turned on the printer and hit auto-home, and discovered a problem: Home position now had the nozzle below the print bed! I went back and checked the adjustment wheels and they were cranked down as tight as I could get them. I ended up raising the Z-axis about 2mm and that looked better, so I adjusted the Z-axis stop switch up until it clicked against the bed. Then I fired up the printer again and auto-homed it. Much better! I could see I had a gap now. I dont know if it was the upgraded parts, luck, or what, but leveling was much quicker. I leveled all four corners, then checked the center and it was dead on. After that I went back around the corners to check them all. The front left needed a tiny tweak and everything else was dead-on. The aluminum knobs are super grippy and very easy to make tiny adjustments. The stock plastic wheels werent terrible, but there are definitely better. Ive run 3 or 4 prints since doing the upgrade, and after that batch was done, I checked the level again. Still dead on , right where I left it! Hoping that continues, and things stay exactly where I put them. The extruder upgrade is really nice as well. It went on without any hassle, and feels way better than the cheap plastic included with the Ender 3. (just make sure when you remove the old one that you support the motor - the extruder is what holds it in place and when you remove the last screw, its going to drop!) The thing I like most about it is that its silver so its MUCH easier to see the hole past the gears that you have to get the filament into. That was a huge struggle for me with the black plastic, and with the new silver extruder, you can see exactly where the filament is going and it slipped right in with no trouble at all. I will say that the spring that came with the extruder was bigger and harder to compress than the stock one, and I didnt like the feel of it installed, so I used the stock spring and its been great so far.

Awesome addition. I bought mostly for the tighter springs, but when i went to replace the extruder covers i noticed that the plastic pieces i was replacing were cracked and about to break! highly recommend these parts. note: you will have to move your Z-stop up a bit due to the change in springs and wheels.

Great product! Easy install and great quality.

Everything was fine except one of the leveling wheels would go on because of bad threads. Springs are great, extruder seems to be of great quality. Not too worried about the wheel, as it was my least needed thing of the package, but still a little disappointing. Other than that Im very satisfied

I recently ordered a Creality Ender 3 v2 as my first venture into the 3D printing world. A friend of mine recently did the same and recommended upgrading a few things right out of the gate. He recommended better bed springs and possibly a better extruder. I ordered this kit which included both of those items. I immediately installed them during the initial build of the printer when it arrived. Because I installed them straight away I have nothing to compare them to so I don’t have a judge of how much better they are than the factory ones. What I do know it the bed levels fairly easily and seems to maintain throughout the print. I usually always re-level the bed before each print as I take the build plate of each time when removing the builds. I can say my friend has had his Ender 3 v2 for about a month and his plastic extruder has already cracked. I guess the extruder upgrade such as the one included in this kit is worth it to avoid the headache.

I recently jumped into the world of 3D printing. Looking at other Ender users, one of the first things that were upgraded were the springs. Very simple to install for a good overall improvement with the bed. I dont find myself constantly leveling the bed now that this kit has been installed.

I have 4 printers. 2 with a similar red kit and this kit which is the silver ones. The metal extruders seem to be the same or same quality on each however this kit has better springs for the bed. These springs are a little beefier and seem to hold the build plate level a little better. Less micro adjusting needed. I would recommend to get some Capricorn tubing with this kit as well and you should be set