













Creality Ender 3 Glass Bed Upgraded Platform 235x235x4mm for Ender 3 S1/ Ender 3 / Ender 3 Pro/Ender 3 V2/ Ender 5/ Ender 5 Pro, 3D Printer Tempered Glass Build Plate Surface
-
Vert E. Breaker
Greater than one weekThis bed isnt quite the same quality as my original Ender 3 V2 bed. I had this bed for about a week and on my 8th or 9th print a piece of the glass bed just came off in the center of the bottom of my print. Its not just a part of the top black printing, an actual piece of the glass came off. You can feel the divot in the glass. This wasnt caused by any tool or anything and you can see it is in the middle of the print where nothing would come in contact anyway. Before this the bed seemed fine and I had no complaints but now Im wondering if this glass bed just had an imperfection that made this happen or if this is something common.
-
Paul Shapiro
> 3 dayI’m using it, but it was slightly warped when I ran Bed Visualizer on it. Not that big a deal, but kind of surprising. Great adhesion otherwise.
-
Cole
Greater than one weekHad problems with adhesion but everything else seems great. May need to mess with heat. Thicker bed may mean I need to increase bed heat
-
Erik G.
> 3 dayBeen using for a bit and havent had any issues yet. Printed dozens of items and all stick and release super easy. There are a couple of different textured glass beds similar to this, and they all work the same way. When the glass bed is heated and printing, the plastic sticks to the texture on the glass since it has little divots. Much easier than just plain glass that is too smooth and wont adhere correctly unless it is perfectly leveled and cleaned. Then once the glass cools, the textured material actually contracts, popping off the print. No need to pry anything off, just a little push or pull and it pops right off. Tip: dont use any glue or anything like that. Just keep it clean and it will work as intended. Also, many people like to use binder clips to hold bed surfaces down, but they get in the way and annoy me. Just use some masking tape along some of the edges and it will stick fine, as shown in my picture.
-
ShareVita.com
Greater than one weekThis thing is so nice, they should ship with the printer. It took about 10 minutes to install and I was off and running. The prints stick when its warm and once it cools off the print just comes right off with no fuss. It makes loveling the bed very easy. Pro tip... Adjust the limit switch and put a piece of tape on the glass bed where the printer head travels to autohome. I almost put a big scratch in mine because the nozzle dragged along the top of the bed.
-
riley
11-06-2025Thicker than Id like perfect on temp but my prints will not stick Ive been using glue and it kind of works but its still better than the stock ender 3 one
-
Joshua
> 3 dayGreat glass bed, a must have if you buy an ender 3 pro printer. Smooth finish on your print and great for high temperature printing
-
Josh Kovach
> 3 dayThis glass build plate arrived quickly (before anticipated delivery date) and came very well packed. Ive been able to use it for a couple days now and have had no issues with bed adhesion or the coating coming off. The glass has no visible dips when leveled. Easier to level than the stock mag flex plate and much flatter. Ill definitely be purchasing a second for my other Ender!
-
Brandon
> 3 dayWorked great when I got it. After about a month, PLA does not adhere well at all anymore. Printing at higher heat and lower first layer helps, but there is always curling now, and smaller prints always fail. Better to find something that wont wear out quite as quickly
-
Tango_542
> 3 dayIts nice arrived super fast, got it out put it on my printer and went back to look for the locking clips...nothing... tried original clips for basic print mat... WAY too small... so now I get to wait a few more days and order some clips, thanks for the heads up...