

Moen 1200 One-Handle Kitchen and Bathroom Faucet Cartridge Replacement, Brass
-
LA Bill
> 3 dayIf you are the original owner and can show receipts, Moen will send one free of charge. Otherwise, this is a good deal on an original Moen part. These brass cartridges work much better for me than the plastic ones commonly found in the big box stores.
-
BuckeyeShopper
06-06-2025I ordered one of these on November 1st, 2012 to replace a plastic stem in our Moen bathroom sink faucet which kept requiring an o-ring replacement or lubrication. I thought maybe being a Genuine Moen part, and of brass construction the sealing valve surfaces for the moving O-rings would be of higher quality and not need such frequent attention. This sink gets a lot of warm water usage, dozens of cycles on this valve every day. As of February 17, 2013 this stem is already worn out, and presents extreme resistance to pulling the faucet handle. I removed it and carefully pulled the inner stem out and cleaned and lubricated it with FDA approved silicone grease, and re-assembled it. It doesnt leak, but it is still hard to pull and actually squeaks when pushed closed. The sealing o-rings look like new, but since half the O-ring seals in this model are mounted inside the barrel into grooves, instead of having all of them mounted in grooves on the removable stem (stupid design!!) it would be very difficult to try to remove the hidden o-rings and get a new set installed without scratching the brass in the process, which could lead to premature damage of any newly installed o-rings. So I am replacing this piece of junk and going back to the cheap plastic style of stem. At least those CAN be serviced, after which they work very well for several months, until their o-rings wear out and need to be replaced and re-greased. Of course, if Moen could simply make a faucet that did not NEED all this attention, I would not be in this predicament. But at least this lasts longer than the lousy single handle Delta model it replaced.
-
M. lyders
> 3 dayI bought two of these cartridges and replaced a shower valve and a sink valve,in 2011. No problems at all both cartridges work great. They are not true Moen parts though. Also used a Moen cartridge puller which worked as it was suppose to. Just make sure to use the little plastic cartridge do-hicky to loosen up the old cartridge before using the puller. And lube up the new cartridge with plumbers grease before installing it. Also take off the little snap ring and pull the inside out of the cartridge and lube the O-rings that are inside also. Hardest part in my opinion is getting the u-clip back into place with the new cartridge installed. Use lots of silicon grease when installing and things go back together really smoothly. Update 11-24-15, Had to replace this cartridge 4 years later. I was disappointed in how long it lasted. Maybe a true Moen part would be worth the extra money after all.
-
Keith S
> 3 dayWorks well once you get the old one out!
-
steven
> 3 dayHad all the parts as a group. Glad I got the tool. Old part stuck very Tight. Followed instructions and my faucet works like a new one. Fast delivery.
-
jo bene
> 3 dayThis item worked exactly as I hoped it would. There were no hitches at the time I used it, and it made my plumbing project proceed smoothly.
-
John C. Hovre
05-06-2025Feb 2019...buy this,its OEM and brass ...nothing else to say
-
Dana E. Weber
Greater than one weekThis is my third or fourth replacement cartridge for as many showers, they install easily and work (if you use them). Just have to remember to exercise them every week or so.
-
Richard J. Brown
> 3 dayBetter then original plastic flow control.Use plumbing lube when installing.
-
William S. Weil
Greater than one weekI was lucky as I was able to take out the old cartridge without too much difficulty. Easy to install and by going online there are you tube videos that show you how to install, which is a great help.